Published Apr 9. 2017 - 11 months ago
Updated or edited Apr 9. 2017

Russian Wasp

Russian fly tyer Dmitri Tseliaritski from St. Peterburg ties som mean looking imitations. Here's an example of his foam wasps

The finished Russian Wasp
The finished Russian Wasp
Dmitri Tseliaritski

I have been connected with Dmitri on Facebook for some time, and have been thoroughly impressed by his skills as a fly tyer. He generously posts long and detailed step-by-step photo series and also posts fly tying videos on YouTube.

I wanted to expose Dmitri's tying to more people and approached him about publishing some patterns here on the Global FlyFisher and he agreed. Most of Dmitri's posts and his videos are in Russian, and even though fly fishing and fly tying is an international language, having an English text and list of materials will probably help the many of us who aren't fluid in Russian. There's also a video in the bottom of the article showing the tying with Dmitri's comments in Russian. impressing imitation of a wasp

The wasp
It floats
The wasp
Dmitri Tseliaritski

The foam wasp

The post from Dmitri that spawned this article was a Facebook post which he simply called Wasp SBS. The first picture showed an impressing imitation of a wasp, but in spite of being very lifelike, it looked fairly simple. Dmitri had added about 30 step-by-step photos showing the tying sequence, and these are the photos, which you also see below in the tying instructions.
I have also added a materials list, which Dmitri has approved. The glue is obviously Russian, and not easy to get for us westerners, but contact cement or thin neoprene glue should to the trick. Use it sparingly. A little goes a long way. The legs are broom bristles, a material that has been mentioned before here, many years ago in this ant article.

Legs and antennae gallore
Legs and antennae galore
Dmitri Tseliaritski
A cnadle and tweezers
Bending the legs
An example
Bending the legs
Dmitri Tseliaritski



Dmitri Tseliaritski


Antennae done

Head foam strip

Glue on hook

Push to the front

Foam block

Trim to shape

Tie in abdomen

Abdomen tied in

Yellow marker


Abdomen done

Front and hind legs

Front legs in position

Middle legs


Legs ready

Bend back foam

Dmitri Tseliaritski
Russian Wasp
Pattern type: 
Dmitri Tseliaritski

A very lifelike foam wasp

Kamasan B100 #12
UNI, black, 8/0
black broom bristles
yellow foam strip
sandwiched foam, covered with a thin layer of LCR
yellow broom bristles, tips colored black
chestnut rooster hackle tips
yellow foam, a little black dubbing
colored black, covered and built up with LCR
you will need warm yellow and black markers as well as varnish and LCR
A little difficult
  1. Start by making the abdomen. Glue together yellow and black craft foam to create a 1-1.5 centimeter or 1/2 inch stack. Cut this into striped rods of about 0.5 x 0.5 centimeters or about 0.2 x 0.2 inches. One rod will form the base for one wasp abdomen.
  2. Start the thread in the front of the hook.
  3. Tie in two black bristles pointing forward, forming the antennae. Just leave them sticking out parallel in the front. Trim off surplus.
  4. Cut a narrow (0.5 cm/ 0.2”) strip of yellow foam. Bend back and glue one end.
  5. Stick the hook through the foam in the center of the bent piece and slide to the front
  6. Glue the foam and press it over the bases of the antennae.
  7. Take the striped foam rod and trim to a tapered shape using a pair of sharp scissors.
  8. Tie in the abdomen leaving a bit of space behind the front foam.
  9. Mark the yellow part with a warm yellow marker if needed.
  10. Cover the abdomen with a thin layer of LCR and cure.
  11. Tin in the hind and front legs in one go, one set on each side.
  12. Cover the front lags with thread, pressing them forward to behind the head foam.
  13. Tie in middle legs as one bristle under the hook.
  14. Varnish the central part of thread over the legs. This will be visible on the finished fly.
  15. Bend back the head foam strip to form the top of the head and tie down.
  16. Cover foam with thread to the middle set of legs.
  17. Dub lightly over the tied down foam.
  18. Bend the foam back forward to right behind the head and tie down.
  19. Trim off surplus foam.
  20. Trim the head to a pointed, tapered shape using sharp scissors.
  21. Use the yellow marker to color the head foam if needed.
  22. Pick two identical, shiny rooster neck feathers.
  23. Strip off the base barbs and tie them in flat, pointing backwards right behind the head.
  24. Trim the feather butts, cover the tie in spot with some dubbing, whip finish and trim thread.
  25. Mark the eyes with a black marker and cover with LCR.
  26. Bend legs and antennae using heated tweezers. Trim to length. Mark the tips of the legs black.

Tie down

Add dubbing

bend forward foam

Trim foam

Shape the head

Color the head

Select hackles

Tie in wings

Whip finish and trim

Dmitri Tseliaritski

Log in or register to pre-fill name on comments, add videos, user pictures and more.
Read more about why you should register.