Published May 12. 2013 - 11 years ago
Updated or edited Jan 5. 2019

Perminator

This rabbit zonker fly imitates a mantis shrimp, a very important food resource for big permit and bonefish, and utilizes the mobile zonker strips to induce life in the fly.

Finished Perminator - The final fly - here in a tan version
Perminator
Pedro Pablo Yañez Duran

History

I made this fly with the idea to imitate a mantis shrimp a very important food resource for big permit and bonefish.

The idea was to make a simple fly with few materials, but durable and full of life under water. The answer was the Zonker strip, a spectacular natural material, which looks full of life underwater, takes an almost translucent appearance and reacts to a minimum water current to make it look alive and entice the fish to strike the fly.

It is a must when you are looking for big permit and bonefish, but also works on other species like striped bass, redfish, corvina and any other shrimp eating species. It's a good step towards successful fishing to match the color of the fly with the bottom of the local environment.

Where to use this fly? At any location - especially in the tropics - where the mantis shrimp are abundant.

How to fish this fly? A good way it is making a few short fast strips and a pause. You can do some long and slow retrieves followed by short and fast strips.

Light olive - Mantis shrimps are often very colorful, s don\'t be afraid of bright colors
Olive perminator gff
Pedro Pablo Yañez Duran
Perminator
Pattern type: 
Warm saltwater fly
Originator: 
Pedro Pablo Yañez Duran
Species: 
Materials: 
Hook
Daiichi X472 #2 or any similar long shank hook
Thread
Lagartun X-strong thread Beige 150 denier
Weight
Brass eyes nickel black large (3/16)
Under tail
Slinky Fiber, color shrimp mixed with Angel Hair color pearl
Tail
Magnum Zonker tan piece 2 inches long
Legs
Centipede legs clear tan
Accent
Krystal flash UV Tan
Eyes
3 millimeter red glass bead on 3 inch piece of 60 lbs fluorocarbon or monofilament covered with Clear Cure Goo Tack Free
Body
Crosscut zonker, tan
Resin
Clear Cure Goo Tack Free and Clear Cure Goo Hydro
Skill level/difficulty: 
Medium
Instruction: 

Step 1

Place the dumbbell eyes near the front of the hook with figure-eight wraps. Cinch the wraps down to the hook shank by wrapping the thread parallel to the shank at the base of the eyes. This pulls the thread even tighter and helps keep the eyes from spinning. Apply a little of Clear Cure Goo Hydro or super glue to secure them in place.

Step 1 - 1 - dumbbell eyes

Step 2

For the tail wrap the thread to the back of the hook shank , then Take a bunch of Slinky Fibers and tie them using the folding method to obtain more volume with less material. At first make just a few loose wraps and push the fibers using the forefinger and thumb together. Pinch the butt ends top to bottom and then side to side to equally distribute the fibers 360 degrees around the hook shank. Take some tight wraps to secure them. Fold back the rest of the fibers and make a few tight wraps and then use Clear Cure Goo Hydro or super glue to secure them in place. Trim the fibers to obtain the desired length and profile. The fibers' length has to be the same as the zonker strip, in this case almost 2 inches.
I recommend using a cardboard cutter blade to give a natural shape. Don't trim the fibers with a straight cut or the fly will look to unnatural.

Step 2 - tail

Step 3

For the upper tail take a 2 inches zonker piece. With hook point riding up poke a hole in the hide where the zonker is penetrated by the hook point. Place zonker over the hook point and lay the strip against the hook shank. Make a few tight wraps to secure it.

Step 3 - 1 - zonker strip

Step 3 - 2 zonker strip ready

Step 3 - 3 - zonker strip in place

Step 4

To create the legs take two strands of centipede legs and place one strand on each side. Tie them folded in half, then take six straws of Krystal flash folded in half on each side of the fly. With this technique we will get 12 strands of Krystal flash per side to create an attractive flashy profile.

Step 4 - Centipede legs

Step 5

To add the eyes tie them in on the side of the hook shank. To obtain the right length, keep almost half inch from the hook gap to the eyes. Make tight wraps to secure them in place then pull them forward to create a V shaped appearance.

Step 5 - eyes

Step 6-7

For the body take a crosscut zonker strip and secure it just behind the eyes and start wrapping the zonker strip. Make tight and neat wraps to just behind the dumbbell eyes. Take the thread and make a few tight wraps to secure it and whip-finish. Apply Clear Cure Goo Tack Free to finish the fly.

Step 6 - body

Step 7 - done

Finished Perminator - The final fly - here in a tan version
Finished fly
Pedro Pablo Yañez Duran

Comments

Very similar to a st...

Very similar to a stillwater pattern in the uk, 'The Bouncing Bomb' designed by a guy called Ben Bangham.

Hi Kate thanks for y...

Hi Kate thanks for your kind words zonker it's an amazing materials my favorite natural by far, gives life to any fly.

All the best
Pedro

This really looks li...

This really looks like a good mantis shrimp imitator. You have used the difficult to tie zonker strip in a very effective way.
Good luck when using this fly.

Pedro, If I wa...

Pedro,
If I was a permit or a bonefish this fly would certainly draw my attention, it does mimic a mantis shrimp. You have used
a normally bulky material in a very effective way. Good job.

.

Log in or register to pre-fill name on comments, add videos, user pictures and more.
Read more about why you should register.
 

Since you got this far …


The GFF money box

… I have a small favor to ask.

Long story short

Support the Global FlyFisher through several different channels, including PayPal.

Long story longer

The Global FlyFisher has been online since the mid-90's and has been free to access for everybody since day one – and will stay free for as long as I run it.
But that doesn't mean that it's free to run.
It costs money to drive a large site like this.

See more details about what you can do to help in this blog post.