The Global FlyFisher - The Largest and Best Place to go for Online Fly Fishing and Fly Tying
First published June 1st 1998 - More than 17 years ago
A bootom seeking fly for pike, cod, pike perch and many other fish
By Martin Joergensen
From thought over drawing to a finished flyOne of the most satisfying aspects of fly tying is in my opinion the chance to design your own fly.
I have come up with many ideas, tied hundreds of flies inspired by them, but mostly thrown them away after having carried them in my fly boxes for some time - either because they were totally unused or because they were unproductive.
Recently I got the idea that I wanted a new type of bottom fly - some kind of sculpin like imitation, with weight, clearly visible eyes and materials with a lot of motion. Of course I have lots of patterns like that already, but who can stand in the way of creativity? I dug out some paper and a pen, and drew the sketch that you see here - a variation of the basic zonker. As with most of my fly ideas, I had a pretty good idea of the looks of the fly, and I also had some general ideas of the materials I wanted to use. These ideas I also listed on the paper. I also knew the tying sequence of this fairly simple fly, and noted that too.
Already while drawing I made the first revisions of the fly. The first version had a fat head made by brushing up a ball of dubbing. I revised that to a head spun by deer hair which is one of my favorite materials. The other major change was turning the hook upside down. This would gain me at least a pair of advantages: getting the hook away from the bottom and hiding the hook point. My experience also tells me that these zonkers have a common problem: the tail often slips down and around the hook bend, and this will effect the appearance and action of the fly. There are a few ways to avoid this. One is to shorten the tail, another to support the tail with a loop of mono, but a third one is to turn the hook upside down. The hook shank penetrating the skin strip will prevent the tail from getting caught in the bend.
I tied the first five flies the same evening that I made the drawing. These were fine, except for one thing. On the original drawing I had a pair of breast fins made from poly yarn. These definately didn't work. They did not look at all like fins, and certainly added a lot of clumsiness to the fly. After a couple of tries with breast fins, I just omitted them on the following three, and the fly still looked good.
Everything acted as I had expected, except for two little things: the rib was a bit difficult to turn the first couple of rounds as the hook tip seemed to be in the way more than is usually the case with zonkers. The other things was more positive: the zonker strip hid the hook point more than I had imagined. This ment a better imitation (in my eyes) but probably also less bottom snags.
I didn't get a chance to fish the fly before I got around to tie it again. This was the evening before leaving for a trip to catch winter cold sea trout in the south west part of the island Seeland where I live.
Now, in the winter the trout tend to be very slow, and often only a colorful fly will get them moving. This is often obtained using flies like the Glitter Shrimp or colorful versions of well known patterns. That inspired me to tie a colorful version of this yet unnamed fly.
The color came from three materials: orange dubbing, a red rabbit zonker strip and orange deer hair. I also used a larger hook to get an even more visible fly. Both this version and the smaller, naturally colored version are quite heavy, but with a little ease, a short stiff leader and some deliberately slow casting movements they will cast easily on a 6 wt. I did so - cast intesively with both flies that cold day on the Danish coast, but caught nothing... but that's a whole other story.
||Tiemco TMC 700 size 2-4
||Oval medium silver tinsel
||Almost any dubbing, I use Scintilla light tan or orange
||Nutria zonker strip
||Bestco painted dumbbell|
||Natural deer hair
||Kamasan B800 size 2-4
||Oval medium silver tinsel
||Almost any orange dubbing, I use Scintilla
||Red rabbit zonker strip
||Bestco painted dumbbell
||Orange deer hair
- Mount the hook upside down in any vice or normal in a truly rotating vice
- Start the thread just over the hook bend. Actually under when the hook is upside down
- Tie in the silver tinsel under the bend. Actually over when the hook is upside down
- Dub two thirds of the body with an even cylindrical layer of dubbing
- Prepare a medium narrow zonker strip of fur
- Measure the strip for length. Make note of the position where the hook will penetrate the skin (Orange arrow on the top drawing).
- Punch the hook through the skin in this spot (2nd drawing)
- Pull the skin tightly up against the body (3rd drawing)
- Tie down the skin in front of the body (3rd drawing)
- Wind the ribbing through the skin in 4-5 open, but tight turns (4th drawing)
- Tie down and cut surplus
- Tie in the eyes on top of the hook shank. Actually under the hook when the hook is upside down (5th drawing)
- Prepare some deer hair. There's no need to stack it
- Flare the deer over the eyes. Keep it under the hook shank. Actually over the hook when the hook is upside down
- Tie in one more bunch if needed
- Add several drops of varnish on the bases of the hair
- Let dry
- Trim the deer hair
|More great articles on The Global FlyFisher|
|These other stories on "Deer Hair - Thick, spongy hair from all kinds of deer" might also interest you:
More about Deer Hair
|A couple of random articles|